Sensaphone Accessories

Water Detection Sensor Back to top
	Detects the presence of water on a horizontal surface. Independently powered by internal lithium batteries. Multiple sensors can be wired in a series to a single input. Dimensions: 2.25" x 1.125" x 3.625".
Smoke Detector with Built-In Relay Back to top
	This photoelectric smoke alarm has 120 VAC input via permanent connection and two sets of dry alarm contacts (one form A, SPST; one form C, SPDT). Horn included. Tandem interconnect capability (maximum 20). Dimensions: 5.1" diameter x 2.5". Weight 6.5 ounces.
Passive Infra-Red Motion Detector Back to top
	Monitors the movement of warm bodies in a specific area. Will cause a dialout if motion is detected. Range of detection covers approximately 50 ft. of area. Multiple sensors can be wired in series to a single input. Dimensions: 4" x 6" x 1.5"
Magnetic Reed Switch Back to top
	Detects any unauthorized entry or intrusion. Usually installed on doors and windows, the sensors monitor their opening and closing. Several magnetic reed switches may be wired in series. Dimensions: 2.5" x 0.75" x 0.5" (part with screw terminals); 2.5" x 0.75" x 0.625" (part with magnet).
Power-Out Alert Back to top
	A compact power outage monitoring device to protect against power outages. The Power-Out Alert easily plugs into any 110 VAC receptacle outlet for operation. Connect the SPST output alarm cable to your Sensaphone and prompt notification of the outage will occur after a fixed 3-8 minute delay. The delay guards against nuisance alarms. Dimensions: 2.25" x 2" x 3" (5.7 cm x 5.1 cm x 7.6 cm)
Phonecell SX3e 800 Mhz Cellular Phone Back to top
	Provides proven, reliable access for your Sensaphone system where phone service is needed and cellular networks are available*. All of your communications requirements, such as voice, fax and data can be easily supported. The Phonecell gives you a full 3 watts of power for reliable signal strength. Simple RJ-11C interface. Compatible with all Sensaphone models! Dimensions: 9.7" x 7.2" x 1.7" (24.6 x 18.3 x 4.3 cm) *Cellular service required through local cellular provider. Optional Power Supplies: Standard plug-in power supply Power Supply with Battery Backup Optional Antennas: 3dB Spike Antenna 9dB Yagi Antenna
Temp Alert Back to top
	Monitors air temperature from -30o to 130o F(-34o to 54o C). Simply determine the acceptable temperature limits for your application by adjusting the temperature limit arms. When temperature exceeds the setting, the sensor triggers an alarm. Can be mounted to any wall or vertical surface. Multiple Tempo Alerts may be wired in parallel to a single input. Dimensions: 6.25" x 3.25" x 2"
2.8K Remote Temperature Sensor Back to top
	Enables you to monitor temperature at a location away from your Sensaphone unit. Measures and tells you the exact temperature and triggers an alarm when conditions exceed the set high/low limits. May be mounted anywhere air temperature needs to be measured and can be used with the following models: 1104, 1108, 4100; Range: -20oF to 150oF Express, Express II and 2000; Range: -60oF to 175oF Only one sensor may be wired per input. Dimensions: 2.5" x .75" x .75"
2.8K and 10K Weatherproof Temperature Probes Back to top
	Small probes, good general purpose devices for indoor/outdoor applications. Sensitive temperature element in a stainless steel housing with a moisture-resistant seal. Convenient mounting clip and 12 feet of wire included. Accurate to +/- 1oF (0.56oC) with a sensing range of -40oF to 175oF. 2.8K may be used with 1104, 1108, 4100, Express, Express II, 2000 10K may be used with Express, Express II, 2000, SCADA 3000 Dimensions: 2" long x 0.25" diameter
10K Indoor Decorator Zone Temperature Sensor Back to top
	Precision room temperature sensing in an attractive wall-mounted enclosure. Accurate to +/-0.36oF (0.2oC) with a sensing range of 35o to 140oF. Beige plastic enclosure, tan metal faceplate For use with Express, Express II, 2000, SCADA 3000 Dimensions: 4.5" x 3.23" x 1.2"
10K Outdoor Air Weatherproof Temperature Sensor Back to top
	Sensitive temperature element. Stainless steel tube sheathe. Mounted inside ventilated, treated weather-resistant PVC shield minimizing radiant energy effects. Mounted on a weatherproof outlet box for easy outdoor installation. Accurate to +/-0.36oF (0.2oC) with a sensing range of -30oF to 140oF. 8 feet of 24AWG wire included. For use with Express, Express II, 2000, SCADA 3000 Dimensions: 9" x 3" x 2"
10K Immersion Temperature Sensor Back to top
	Waterproof for measuring the temperature of fluids inside a pipe. 304 stainless steel probe. Brass WEL-B thermowell (screws into customer-supplied 0.5" NPT saddle or Thredolet fitting in pipe). Fits into thermowell via brass 0.125" NPT fitting. Accurate to +/-0.36oF (0.2oC) with a sensing range of 10oF to 230oF. Includes 8 feet of 24AWG wire. For use with Express, Express II, 2000, SCADA 3000 Dimensions: Thermowell 5.125", Sensor in well 6.5"
Humidistat Back to top
	Can be used with all Sensaphone models to detect too high or too low a humidity level. Range of the humidistat is 10% to 60% RH. The sensor causes an alarm when the humidity exceeds or falls below the set limit. Multiple sensors may be wired to a single input. Dimensions: 4.125" x 2.75" x 1.5"
Humidity Transmitter Back to top
	Space-mount, low-profile model has 10 point calibration accuracy and features a bulk polymer resistive sensor. 3% accuracy at 20 to 95% RH. Typical drift is less than 1% per year. The sensor output signal is field-selectable from 0-5 volt, 0-10 volt, or 4-20mA. Prewired base makes installation easy. For use with Express II, 2000, SCADA 3000 Dimensions: 4.9" x 3.1" (12.4cm x 7.9cm); Weight: 0.2 lb (0.9 kg)
Buy Sensaphone autodialers online...all with free standard shipping!!! Click here to visit our online store: www.hnscompany.com/store